Android Video Flashing Network Boot Tutorial

From OMAPpedia

Revision as of 22:00, 14 June 2010 by Hari s (Talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Contents

[edit] Tutorial #2 - Flashing Bootloader, TFTP Kernel, and NFS

This tutorial will help setup an environment more suitable for debugging. The bootloaders will load from flash, the kernel will load from a TFTP server, and the Android file system will run via NFS over Ethernet.

Prerequisite : Android_Video_Run_From_SD Tutorial #1 - Android running from SD card

Key #HT (Hypertermianl prompt) $ (Ubuntu terminal prompt)

[edit] Setup TFTP on Linux PC

$ sudo apt-get install xinetd tftpd tftp
$ sudo gedit /etc/xinetd.d/tftp
// Add the following, save and exit
service tftp
{
protocol = udp
port = 69
socket_type = dgram
wait = yes
user = nobody
server = /usr/sbin/in.tftpd
server_args = -s /home/user/tftpboot
disable = no
}
//create directory
$ sudo mkdir /home/user/tftpboot
$ sudo chmod -R 777 /home/user/tftpboot
$ sudo chown -R nobody /home/user/tftpboot
$ sudo /etc/init.d/xinetd stop
$ sudo /etc/init.d/xinetd start
//copy files
$ cd /home/user/tftpboot
$ cp /home/user/l25.7/mydroid/bootloader/x-loader/MLO .
$ cp /home/user/l25.7/mydroid/bootloader/u-boot/u-boot.bin .
$ cp /home/user/l25.7/mydroid/kernel/arch/arm/boot/uImage .
// use ifconfig to determine ip address - and use this for bootargs and serverip
$ ifconfig


[edit] Setup NFS

$ sudo aptitude -P install nfs-kernel-server nfs-common portmap
//Specifically choose "No Loopback" to enable listening on other IPs
$ sudo dpkg-reconfigure portmap
$ cd /etc
$ gedit exports
//add this line
/home/user/l25.7/myfs *(rw,sync,no_subtree_check,no_root_squash)
//make changes effective
$ sudo exportfs -rav
//$ sudo exportfs -a //Edit: Commented this out. using options -rav
$ sudo /etc/init.d/nfs-kernel-server restart

[edit] Writing XLoader & U-Boot to NAND

// UBOOT and MLO (xloader) should be in tftpboot directory
//  setup to configure bootargs - like in tutorial #1
 

HT# nand unlock
HT# nand ecc sw
HT# setenv serverip 128.247.77.47
HT# dhcp 80008000 u-boot.bin
HT# nand unlock; nand ecc sw; nand erase 80000 40000; nand write 80008000 80000 40000
HT# nand unlock
HT# nand ecc sw
HT# setenv serverip 128.247.77.47
HT# dhcp 80008000 MLO
HT# nand unlock; nand ecc hw; nand erase 0 40000; nand write 80008000 0 40000

[edit] Setup Bootargs to use NFS & TFTP -- Then Boot!

HT# nand unlock
HT# nand ecc sw
HT# setenv serverip 128.247.77.47
HT# setenv bootfile 'uImage'
HT# setenv bootargs console=ttyS3,115200n8 noinitrd mem=112M root=/dev/nfs rw nfsroot=128.247.77.43:/home/user/l25.7/myfs/,nolock,wsize=1024,rsize=1024 ip=dhcp init=/init
HT# setenv bootcmd 'dhcp 80300000 uImage; bootm'
HT# saveenv
HT# printenv
HT# boot
Personal tools
Namespaces
Variants
Actions
Navigation
Toolbox